Skip to main content

Posts

Showing posts from August, 2019

3pcs HC-06 bluetooth RF Transceiver RS232 With Backplane Wireless Serial 4P 4 Pin Module Board For Arduino

Get 3pcs HC-06 bluetooth RF Transceiver RS232 With Backplane Wireless Serial 4P 4 Pin Module Board For Arduino Features:   Allows your device to both send or receive the TTL data via Bluetooth technology without connecting a serial cable to your computer. Commercial Series: Bluetooth module board Series With LED indicator light, use 150mA and 3.3V regulation chip. With VCC. GND. TXD. RXD foot for the Bluetooth With "Research" button(ON/OFF/WAKE foot for it, external MCU output "High level" can control module to research) Compatible with bluetooth master module".slave module"or master-slave(whole) module. Input voltage: 3.3~6V Size: 1.55 x 3.98cm   Specification:   Works with any USB Bluetooth adapters. Default Baud Rate: 9600,8,1,n. Built-in antenna. Coverage up to 30ft. Bluetooth version: V2.0+EDR Operating voltage: 3.3V Default Baud Rate: 9600,8,1,n. Signal coverage: 30ft Cable length: about 21.5cm Item size

20pcs BESTEP 1 Channel 3.3V Low Level Trigger Relay Module Optocoupler Isolation Terminal For Arduino

Get 20pcs BESTEP 1 Channel 3.3V Low Level Trigger Relay Module Optocoupler Isolation Terminal For Arduino Description:   Normally open interface maximum load: AC 250V/10A, DC 30V/10A. SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA. Fault-tolerant design, the relay will not move even if the control line is broken. Power indicator (green), relay status indicator (red). The interface is designed humanized, and all the interfaces can be directly connected by wiring terminals, which is very convenient. Two module interface:   1. DC+: Connect the power supply positive pole (voltage 3.3V). 2. DC-: Connect the power negative pole. 3. IN: Low level (3.3V) control relay pull in.   Relay output terminal:   1. NO: Relay normal open, the relay suspends before pulling in, and then short-connect with the COM. 2. COM: Relay common interface 3. NC: Relay normal close, short connected with COM before pul

10pcs BESTEP 1 Channel 3.3V Low Level Trigger Relay Module Optocoupler Isolation Terminal For Arduino

Get 10pcs BESTEP 1 Channel 3.3V Low Level Trigger Relay Module Optocoupler Isolation Terminal For Arduino Description:   Normally open interface maximum load: AC 250V/10A, DC 30V/10A. SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA. Fault-tolerant design, the relay will not move even if the control line is broken. Power indicator (green), relay status indicator (red). The interface is designed humanized, and all the interfaces can be directly connected by wiring terminals, which is very convenient. Two module interface:   1. DC+: Connect the power supply positive pole (voltage 3.3V). 2. DC-: Connect the power negative pole. 3. IN: Low level (3.3V) control relay pull in.   Relay output terminal:   1. NO: Relay normal open, the relay suspends before pulling in, and then short-connect with the COM. 2. COM: Relay common interface 3. NC: Relay normal close, short connected with COM before pul

5pcs BESTEP 1 Channel 3.3V Low Level Trigger Relay Module Optocoupler Isolation Terminal For Arduino

Get 5pcs BESTEP 1 Channel 3.3V Low Level Trigger Relay Module Optocoupler Isolation Terminal For Arduino Description:   Normally open interface maximum load: AC 250V/10A, DC 30V/10A. SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA. Fault-tolerant design, the relay will not move even if the control line is broken. Power indicator (green), relay status indicator (red). The interface is designed humanized, and all the interfaces can be directly connected by wiring terminals, which is very convenient. Two module interface:   1. DC+: Connect the power supply positive pole (voltage 3.3V). 2. DC-: Connect the power negative pole. 3. IN: Low level (3.3V) control relay pull in.   Relay output terminal:   1. NO: Relay normal open, the relay suspends before pulling in, and then short-connect with the COM. 2. COM: Relay common interface 3. NC: Relay normal close, short connected with COM before pull

3pcs BESTEP 1 Channel 3.3V Low Level Trigger Relay Module Optocoupler Isolation Terminal For Arduino

Get 3pcs BESTEP 1 Channel 3.3V Low Level Trigger Relay Module Optocoupler Isolation Terminal For Arduino Description:   Normally open interface maximum load: AC 250V/10A, DC 30V/10A. SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA. Fault-tolerant design, the relay will not move even if the control line is broken. Power indicator (green), relay status indicator (red). The interface is designed humanized, and all the interfaces can be directly connected by wiring terminals, which is very convenient. Two module interface:   1. DC+: Connect the power supply positive pole (voltage 3.3V). 2. DC-: Connect the power negative pole. 3. IN: Low level (3.3V) control relay pull in.   Relay output terminal:   1. NO: Relay normal open, the relay suspends before pulling in, and then short-connect with the COM. 2. COM: Relay common interface 3. NC: Relay normal close, short connected with COM before pull