Skip to main content

5pcs Geekcreit® 7Pin 0.96 Inch OLED Display 12864 SSD1306 SPI IIC Serial LCD Screen Module For Arduino

5pcs Geekcreit® 7Pin 0.96 Inch OLED Display 12864 SSD1306 SPI IIC Serial LCD Screen Module For Arduino
5pcs Geekcreit® 7Pin 0.96 Inch OLED Display 12864 SSD1306 SPI IIC Serial LCD Screen Module For Arduino 5pcs Geekcreit® 7Pin 0.96 Inch OLED Display 12864 SSD1306 SPI IIC Serial LCD Screen Module For Arduino 5pcs Geekcreit® 7Pin 0.96 Inch OLED Display 12864 SSD1306 SPI IIC Serial LCD Screen Module For Arduino



Feature:
 
Control chip: SSD1306
Display area: 21.744 x 10864mm
Physical size: 27.3 x 27.8mm
Interface type: Default 4-wire SPI
Switchable rear resistor to use 3-wire SPI, IIC interfaces
Number of pins: 7
Display color: yellow blue
Working temperature: -40~70°C
Net weight: 5g
 
Interface definition:
 
1> GND (Power ground)
2> VCC (Power + 3.3-5V)
3> D0 (SPI clock line for SPI interface and IIC clock line for IIC interface)
4> D1 (SPI data line for SPI interface and IIC data line for IIC interface)
5> RES (OLED reset, OLED needs to be reset once after power-on)
6> DC (SPI data/command selection pin, used to set IIC address when IIC interface)
7> CS (OLED SPI chip select, active low, if you do not want to use must be grounded)
 
Package includes:
 
5 x 0.96 Inch OLED Display Module

Wiring method:


Wiring 1:
MCU hardware SPI connection method:
If there is only one device on the SPI bus, you can directly ground the CS of the OLED screen, which saves an IO.

Wiring 2:
MCU IO analog SPI connection mode:
If there is only one device on the SPI bus, you can directly ground the CS of the OLED screen, which saves an IO.

Wiring 3:
MCU analog IIC connection method:
IIC address:
DC is low = 0x78
DC is high = 0x7A
Generally DC grounding
 
Wiring 4:
MCU hardware IIC connection method:
IIC address:
DC is low = 0x78
DC is high = 0x7A
Generally DC grounding

As below pictures show: 


























5pcs Geekcreit® 7Pin 0.96 Inch OLED Display 12864 SSD1306 SPI IIC Serial LCD Screen Module For Arduino See detail


Popular posts from this blog

SX1308 DC-DC 2V-24V to 2V-28V 2A Adjustable Boost Regulated Power Supply Module High Current

Get SX1308 DC-DC 2V-24V to 2V-28V 2A Adjustable Boost Regulated Power Supply Module High Current Introduction:   The SX1308 boost module is equipped with the SX1308 chip, which has a small package and high efficiency. The output is adjustable up to 28V, and the internal integration of very low RDS internal resistance 100mΩ metal oxide semiconductor field effect transistor (MOSFET) can achieve high current output within 2A. Widely used in 3G network products, digital products, mobile power, battery-powered equipment.   Features:   Oscillation frequency 1.2MHz, efficiency up to 95% The circuit has short circuit protection, overheat protection and other functions 10K price potentiometer, adjust voltage output   Parameters:   Input voltage range: DC 2V-24V Output voltage range: DC 2V-28V Switching frequency: 1.2MHz Output current: ≤ 2A Package includes: 1 x Power supply module SX1308 DC-DC 2V-24V to 2V-28V 2A Adjustable Boost Regulate...

LM2596S DC-DC 24V/12V To 5V 5A Step Down Power Supply Buck Converter Adjustable USB Step-down Charging Module

Get LM2596S DC-DC 24V/12V To 5V 5A Step Down Power Supply Buck Converter Adjustable USB Step-down Charging Module Features: Synchronous rectification scheme, wide voltage input, high current output, high efficiency. With DC plug and terminals, easy to use. With USB port, with fast-charge identification chip compatible with Andrews and iphone mobile phone.   Product parameters:   Input voltage: DC 9V - 36V The output voltage: 5.2V / 5A / 25W Output capability:  9 ~ 24V Input: Output 5.2V / 6A / 30W                              24 ~ 32V Input: Output 5.2V / 5A / 25W                              32 ~ 36V Input: Output 5.2V / 3.5A / 18W Size: 63 x 27 x 10mm (L * W * H) Weight: 22g   Package included: 1 x LM2596S DC-DC 24V/12V To 5V 5A Step Down Module LM2596S DC-DC 24V/12V To 5V 5A Step Down Power Supply Buck Converter Adjustable USB Step-down Charging Module See detail

ESP01 Programmer Adapter UART GPIO0 ESP-01 CH340G USB to ESP8266 Serial Wireless Wifi Development Board

Get ESP01 Programmer Adapter UART GPIO0 ESP-01 CH340G USB to ESP8266 Serial Wireless Wifi Development Board Description:   This module is a USB adapter/programmer for ESP8266 modules of type ESP-01. It is conveniently fitted with a 2x4P 2.54mm female header to plug the ESP01 (according to illustration picture 2) and configure or run it right away. A large 1000μF cap will help to get a steady 5.0V VCC from the USB bus and jumper (on the right of the 2x4P header)(we don't offer any jumper !!!!) will help to configure the GPIO0 line according to needs. The module is based on the USB-UART bridge CH340 from WCH which is compatible with all platforms.   Note:   For a usage with Arduino ESP8266 platform and for Arduino IDE it is necessary to switch manually the GPIO0 state for working mode, in order to get a fully automatic upload it is most likely possible, for a very limited effort, to assign an unused control line from CH340 to driver the ...